![]() ![]() Happy cord replacing! As for me, I am headed for the store, as I am not so sure I can remember how to get the darn thing put back together. Now you can see all the wiring necessary to cut and splice. If you’ve made it this far, then gently pry apart the motor halves keeping even as yo do. Once you have the main body housing cover off, then you can access the 2 screws atop of each trunnion cover that holds the motor assembly cover halves together. Here’s a link to a schematic that might help as you attempt to do this, (assuming that you still do!) To do that, obviously the 4 screws holding the bottom plate need to come off too. Then to get the colored housing off you need to access 2 screws on the underside that are beneath the agitator roller. but the 5 screws on the front housing DO: 2 above the light and 3 below it. If you continue to experience issues, consider contacting Hoover’s customer support or taking your vacuum to a professional for further assistance.ANSWER : The aforementioned solutions probably never even attempted this fix on this model. Replace worn belts: Check the flat belt for wear and replace it if it is stretched, cut, or broken.īy following these steps, you can effectively reset your Hoover WindTunnel vacuum and ensure it continues to perform optimally.Clean the brush roll: Remove hair, debris, and tangled fibers from the brush roll regularly.Check for clogs and blockages: Inspect the hose, attachments, and air passages for any clogs or blockages.Clean and replace filters: Clean the filters at least once a month and replace them annually.Regularly empty the dust container: Empty the dust container when it is 2/3 full to maintain optimal suction power.Maintaining your Hoover WindTunnel vacuum can prevent the need for frequent resets. Maintaining Your Hoover WindTunnel Vacuum Allow the vacuum to cool: If the vacuum has overheated, unplug it and let it cool for 30 minutes.Empty the dust container: A full container can cause a loss of suction and not allow more dust to be stored in the container.Check the power source: Make sure the vacuum is properly plugged in.Inspect the belt: Check if the belt connecting the brush roll to the vacuum is damaged or broken.Wash the rinsable filter with water, but do not wash the HEPA filter. Clean or replace filters: Ensure that the rinsable filter and HEPA filter are clean.Use a long object, such as a dowel or ruler, to push debris through the suction hose. Check for clogs: Inspect the hose, brush roll, and other parts of the vacuum for any obstructions.If the reset doesn’t work, you can follow these troubleshooting steps: Plug the vacuum back into the electrical outlet and turn it on.Inspect the filters for dirt or damage, clean or replace them accordingly.Remove any debris obstructing the airway and ensure the hose is securely attached. Check for any clogs or blockages in the hose, attachments, and airways. ![]() Unplug the vacuum cleaner from the electrical outlet.Now, follow these steps to reset your Hoover WindTunnel vacuum: Use only attachments, consumables, or spares recommended or supplied by Hoover.Keep hands, feet, loose clothing, and hair away from rotating brushes.If damaged, stop using the appliance immediately and have it replaced by an authorized Hoover service engineer. Inspect the power cord for any damage.Make sure the vacuum cleaner is placed on a stable surface to prevent it from falling.Do not use the vacuum cleaner in areas with flammable or explosive substances.Unplug the vacuum cleaner from the electrical outlet to avoid any risk of electric shock.How to Safely Reset Your Hoover WindTunnel Vacuumīefore attempting to reset your Hoover WindTunnel vacuum, ensure you take these safety precautions: Filter Replacement: If you have replaced the HEPA filter or any other filters in the vacuum, you might need to reset the vacuum to ensure it functions properly with the new filters. Brush Roll Issues: If the brush roll is not spinning or is tangled with debris, you may need to reset the vacuum after cleaning or replacing the brush roll.Ĥ. Clogs or Blockages: If the vacuum is not picking up dirt or debris properly, there might be a clog or blockage in the hose, brush roll, or filters.ģ. Overheating: If the vacuum overheats, it may shut off automatically to protect the motor.Ģ. You need to replace it, call or email hoover to order part and inquire for availability on this LINK Remedy, if you need to use your vacuum immediately and temporary use it, I will give you the remedy but you have to replace the switch as soon as the part arrived. The Hoover WindTunnel vacuum may need to be reset due to:ġ. Unfortunately, this switch is unrepairable. If the vacuum still doesn’t work properly, it may need further troubleshooting. Finally, plug the vacuum back into the electrical outlet and turn it on. Inspect the filters for dirt or damage, and clean or replace them if necessary. Check for any clogs or blockages in the hose, attachments, and airways, and remove any debris. To reset your Hoover WindTunnel Vacuum, first unplug it from the electrical outlet. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |